GEO5 :: REI SOFTWARE CO., LTD. | โปรแกรม

Plate – Foundation and roof plate analyses by the Finite Element Method (FEM)

( 65.00 Bytes )

The program performs the analysis of foundation and roof plates of any shape using the Finite Element Method.

Main features

Automatic mesh generator elements with mesh refinement around points or lines
Modelling of subsoil or piled foundation under the plate
Concentrated and distributed supports (fixed, spring)
Winkler-Pasternak subsoil (parameters of subsoil C1, C2)
Simple introduction of beams using cross-section parameters
Force and deformation loads
Any number of loadcases
Arbitrary number of load cases and combinations
Automatic generator of load combinations according to EN 1990
Determination of required bending and shear reinforcement
Data import-export in DXF format


		Geo 5 Software GEO5 Analytical Solutions GEO5 analytical programs solve common geotechnical problems such as the analysis of sheeting structures and foundations, slope stability, terrain models a...


		FEM – Modelling of various geotechnical problems by the finite element method (FEM) The program can model a wide range of geotechnical problems including terrain settlement, sheet piling/diaphragm walls, underpinning of structures, slope stability...


		FEM - Tunnel – Analysis of tunnels by the Finite Element Method Tunnel* is the extension module of the FEM program. In addition, the Tunnel contains the following capabilities:

		FEM - Water Flow – Analysis of steady state water flow in mass body Module Water flow extends the program FEM*. The module serves to perform steady state analysis of water flowing t...


		Beam – Beams on elastic foundations The program provides the analysis of foundation beams resting on elastic subsoil. Main features Winkler – Pasternak subsoil (parameters of subsoil C1...


		Micropile – Verification of a tubular micropile The program verifies tubular micropiles (micropiles reinforced by a steel tube). When calculating the micropile bearing capacity, the program checks both the micropile root and sha...


		Pile CPT – Verification of piles based on CPTs The program verifies the bearing capacity and settlement of either an isolated pile or a group of piles based on the results provided by static penetration tests (CPT) Mai...


		Piles – Verification of a single pile The program is designed to verify vertical bearing capacity of a pile loaded both in tension and compression, pile settlement as well as bearing capacity of a solitary pile. Verifi...


		Plate – Foundation and roof plate analyses by the Finite Element Method (FEM) The program performs the analysis of foundation and roof plates of any shape using the Finite Element Method. Main features Automatic mesh generator elemen...


		Spread Footing – Design and verification of spread footings This program for the design of spread footings subject to general loading. It computes bearing capacity, settlement and rotation of a footing, and determines required longitudinal ...


		Sheeting Design – Design of sheeting structures and sheet pile walls The program is used to design sheet pile structures. It provides required pile embedment lengths (for fixed and hinged toes), pile bending moments, internal forces and anchor loads...


		Sheeting Check – Analysis of pile sheeting (dependent pressures) The program is for the analysis of sheeting structures (anchored, strutted and non-anchored structures) by the method of dependent pressures i.e. the magnitude of pressures acting ...


		Abutment – Verification of bridge abutments The program serves to verify abutment design. It allows for checking the abutment for overturning, translation, bearing capacity of foundation soil and for dimensioning of decisive...


		Cantilever Wall – Design and check of cantilever retaining wallsThe program is used to verify cantilever wall design. The program is used to verify cantilever wall design. It offers a number of wall shapes and checks reinforced concrete cross-sections. Main features ...


		Earth Pressures – Calculation of earth preassures The program computes basic earth pressures (active, passive pressure, and pressure at rest) acting upon an arbitrary curved structure. Main features Genera...


		Gabion – Verification of gabion walls The program is used to verify the design of walls built from wired baskets filled with rock (gabions). It allows the analysis of arbitrary shapes including overhangs requiring anch...


		Gravity Wall – Design and check of gravity retaining walls The program is used to verify gravity wall design. It offers a number of wall shapes and checks mass concrete cross-sections. Main features Ver...


		Masonry Wall – Design checking of reinforced masonry retaining walls Verification of reinforced masonry walls. Main features Verification analysis can be performed employing EN 1997-1, LRFD or classical approach ...


		Nailed Slopes – Analyses of soil nailed retaining structures The program analyses nailed walls and slopes of various shapes. Main features Verification analysis can be performed employing EN 1997-1, LRFD ...


		Prefab Wall – Design and design checking of prefabricated retaining walls The program is used to verify retaining walls made from prefabricated blocks. Main features Verification analysis can be performed employing EN...


		Redi Rock Wall – Retaining wall design The program Redi Rock wall is used to design and check a retaining walls made from blocks produced by Redi-Rock, Inc (USA).<...


		Slope Stability – Slope stability analysis The program analyses the stability of generally layered soil slopes. It is used mainly for stability checks of embankments, earth cuts and anchored sheeting structures. The...


		Rock Stability – Analysis of rock slope stability The program analyses the stability of rock slopes and walls for a specified type of failure, including a planar or polygonal slip surface or soil (rock) wedge. Main featur...


		Ground Loss – Risk assessment of building damage due to tunneling The program is designed to analyse and determine the shape of the subsidence trough above excavations and to evaluate the damage to buildings situated in the affected area.


		Settlement – Soil settlement analysis Settlement caused by surcharge or change of ground water table (GWT). Main features Various theories of settlement analysis (Janbu, Buisman, Soft soil, usi...


		Terrain – Digital model of terrain (DTM) The program creates digital terrain models from input data points and holes. Main features Generation of the digital terrain model (DTM) from input points,...

Main features

Main features

Mai...

Main features

Main features

Main features

Main features

Main features

Main features

Main features

Main featur...

Main features

Main features